ad9081: PR review changes

StancaPop · StancaPop · commit 7fc8636a3cb4 · 2025-12-12T16:19:08.000+02:00
Signed-off-by: Stanca Pop &lt;stanca.pop@analog.com&gt;
diff --git a/docs/solutions/reference-designs/eval-ad9081/index.rst b/docs/solutions/reference-designs/eval-ad9081/index.rst
@@ -97,7 +97,7 @@ Table of contents
       #. Using the :ref:`VCK190 & VPK180/Versal <ad9081 quickstart vck190>`
       #. Using the :ref:`VCU118/ Virtex UltraScale+ <ad9081 quickstart vcu118>`
       #. Using the :ref:`ZC706/ Zynq-7000 SoC <ad9081 quickstart zc706>`
-      #. Using the :ref:`ZCU102/Zynq UltraScale MP SoC <ad9081 quickstart zcu102>`
+      #. Using the :ref:`ZCU102/Zynq UltraScale+ MP SoC <ad9081 quickstart zcu102>`
 
 
    #. Configure an SD Card with :external+adi-kuiper-gen:doc:`Kuiper <index>`
diff --git a/docs/solutions/reference-designs/eval-ad9081/quickstart/a10soc.rst b/docs/solutions/reference-designs/eval-ad9081/quickstart/a10soc.rst
@@ -135,8 +135,8 @@ and the DAC channels on the evaluation board, using SMA cables.
 Follow the steps in this order, to avoid damaging the components:
 
 #. Connect the SMA cables ADC0-DAC0, ADC1-DAC1, ADC2-DAC2, ADC3-DAC3
-#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier **HPC1** FMCA (J29) socket
+#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the A10SOC
+   **HPC1** FMCA (J29) socket
 #. Both the HPS (J26) and FPGA (J27) memory module must be installed on the
    A10SoC
 #. Insert microSD card into the card socket on the FPGA
@@ -683,7 +683,8 @@ To reboot the system, run:
 
 .. include:: ../../common/using-iio-osc.rst
 
-About the IIO devices
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 ..
+   About the IIO devices
+   ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+   
    TBD
diff --git a/docs/solutions/reference-designs/eval-ad9081/quickstart/vck190.rst b/docs/solutions/reference-designs/eval-ad9081/quickstart/vck190.rst
@@ -76,10 +76,10 @@ Follow the steps in this order, to avoid damaging the components:
 
 
 #. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier FMC+ FMCP1 socket
+   VCK190 FMCP1 socket
 #. Connect USB UART J207 (Type-C USB) to your host PC
 #. Insert SD card with ADI Kuiper image into socket J302
-#. Insert System Controller SD card into socket J206
+#. Insert System Controller micro SD card into socket J206
 #. Configure ACAP for SD boot (mode SW1[4:1] switch in the position
    **OFF,OFF,OFF,ON** as seen in the below picture)
 
@@ -112,7 +112,7 @@ Follow the steps in this order, to avoid damaging the components:
       :width: 1000
 
 #. On the ACAP UART interface console, reboot the system. After reboot,
-   ad9081 devices should be present.
+   AD9081 devices should be present.
 
    .. note::
 
@@ -872,8 +872,8 @@ To reboot the system, run:
 
 .. include:: ../../common/using-iio-osc.rst
 
-About the IIO devices
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
 ..
+   About the IIO devices
+   ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+   
    TBD
diff --git a/docs/solutions/reference-designs/eval-ad9081/quickstart/vcu118.rst b/docs/solutions/reference-designs/eval-ad9081/quickstart/vcu118.rst
@@ -75,8 +75,8 @@ and the DAC channels on the evaluation board, using SMA cables.
 Follow the steps in this order, to avoid damaging the components:
 
 #. Connect the SMA cables ADC0-DAC0, ADC1-DAC1, ADC2-DAC2, ADC3-DAC3
-#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier **FMC+** socket
+#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the VCU118
+   **FMC+** socket
 #. Insert SD card into the SD card socket on the FPGA
 #. Configure :xilinx:`VCU118` for SD card boot mode (mode SW6[3:1] switch in
    the position **1: Down, 2: Down, 3: Up, 4: Up** )
@@ -196,9 +196,10 @@ To reboot the system, run:
 
 .. include:: ../../common/using-iio-osc.rst
 
-About the IIO devices
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 ..
+   About the IIO devices
+   ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+   
    TBD
 
 Using no-OS as software
@@ -249,8 +250,8 @@ Creating the setup
 
 Follow the steps in this order, to avoid damaging the components:
 
-#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier **FMC+** socket
+#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the VCU118
+   **FMC+** socket
 #. Configure :xilinx:`VCU118` for SD card boot mode (mode SW6[3:1] switch in
    the position **1: Down, 2: Down, 3: Up, 4: Up** )
 #. Connect USB UART (Micro-USB) to your host PC
diff --git a/docs/solutions/reference-designs/eval-ad9081/quickstart/zc706.rst b/docs/solutions/reference-designs/eval-ad9081/quickstart/zc706.rst
@@ -73,8 +73,8 @@ and the DAC channels on the evaluation board, using SMA cables.
 Follow the steps in this order, to avoid damaging the components:
 
 #. Connect the SMA cables ADC0-DAC0, ADC1-DAC1, ADC2-DAC2, ADC3-DAC3
-#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier **HPC** FMC socket
+#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the ZC706
+   **HPC** FMC socket
 #. Insert SD card into the SD card socket on the FPGA
 #. Configure :xilinx:`ZC706`` for SD card boot mode (Set the jumpers:
    The main one is: SW11 - Big Blue Switch in the middle, which controls the
@@ -700,10 +700,10 @@ To reboot the system, run:
 
 .. include:: ../../common/using-iio-osc.rst
 
-About the IIO devices
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
 ..
+   About the IIO devices
+   ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
    TBD
 
 Using no-OS as software
@@ -754,8 +754,8 @@ Creating the setup
 
 Follow the steps in this order, to avoid damaging the components:
 
-#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier **HPC** FMC socket
+#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the ZC706
+   **HPC** FMC socket
 #. Configure :xilinx:`ZC706`` for SD card boot mode (Set the jumpers:
    The main one is: SW11 - Big Blue Switch in the middle, which controls the
    Boot Mode, it needs to be set: **1: Up, 2: Up, 3: Up, 4: Up, 5: Down**.
@@ -777,6 +777,7 @@ connected to the proper ttyUSB or COM port:
 
       Xilinx Zynq First Stage Boot Loader
 
-      TBD
+..
+    TBD
 
 .. include:: ../../common/using-iio-osc.rst
diff --git a/docs/solutions/reference-designs/eval-ad9081/quickstart/zcu102.rst b/docs/solutions/reference-designs/eval-ad9081/quickstart/zcu102.rst
@@ -73,8 +73,8 @@ and the DAC channels on the evaluation board, using SMA cables.
 Follow the steps in this order, to avoid damaging the components:
 
 #. Connect the SMA cables ADC0-DAC0, ADC1-DAC1, ADC2-DAC2, ADC3-DAC3
-#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier **HPC1** FMC1 socket
+#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the ZCU102
+   **HPC1** FMC1 socket
 #. Insert SD card into the SD card socket on the FPGA
 #. Configure :xilinx:`ZCU102` for SD card boot mode (mode SW6[4:1] switch in
    the position **OFF,OFF,OFF,ON** as seen in the below picture)
@@ -1081,8 +1081,8 @@ Creating the setup
 
 Follow the steps in this order, to avoid damaging the components:
 
-#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the
-   FPGA carrier **HPC1** FMC1 socket
+#. Connect the :adi:`EVAL-AD9081` / :adi:`EVAL-AD9082` FMC board to the ZCU102
+   **HPC1** FMC1 socket
 #. Configure :xilinx:`ZCU102` for JTAG boot mode (mode SW6[4:1] switch in
    the position **ON,ON,ON,ON**)
 #. Connect USB UART J83 (Micro USB) to your host PC
