Skip to content

HAL configuration

Jump to bottom
Frederic Pillon edited this page Mar 23, 2020 · 9 revisions

HAL module configuration

core version <= 1.5.0

Each variants had to include a STM32 HAL configuration file named stm32yyxx_hal_conf.h. Where yy is one of the supported STM32 series in lowercase (ex: f2).

File can be:

  • generated thanks STM32CubeMX. Copy the stm32yyxx_hal_conf.h file generated to the Inc/ folder to variant folder.

  • copied from a STM32CubeYY project examples (where YY is the MCU serie)

Example name for the Nucleo-F207ZG: stm32f2xx_hal_conf.h

If you copied the variants/board_template folder, stm32yyxx_hal_conf.h have to be deleted.

Then edit copied file in order to:

  • Remove line: #include "main.h"
  • Enable/Disable (un)desired HAL modules by (un)commenting line like: #define HAL_XXX_MODULE_ENABLED where "_XXX_" is the feature (ETH, I2S,...)
  • Adjust HSE/HSI values adaptation if needed
  • Update any other configurations if needed

Below HAL module have to be disabled, they are handled thanks Arduino menu:

  • HAL_UART_MODULE_ENABLED
  • HAL_PCD_MODULE_ENABLED

core version > 1.5.0

Since core version greater than 1.5.0, a default STM32 HAL configuration is provided per STM32 series. As those files were almost the same for the same series, a default one per series avoid to add one for each variant.

Each required STM32 HAL configuration file is in system/STM32YYxx/ (where YY is the MCU serie).

It allows to wrap to the correct HAL configurations. Example for a STM32F2: stm32f2xx_hal_conf.h

/* STM32F2xx specific HAL configuration options. */
#if __has_include("hal_conf_custom.h")
#include "hal_conf_custom.h"
#else
#if __has_include("hal_conf_extra.h")
#include "hal_conf_extra.h"
#endif
#include "stm32f2xx_hal_conf_default.h"
#endif

Each stm32yyxx_hal_conf_default.h file disabled all HAL modules and include the same stm32yyxx_hal_conf.h file available here: cores/arduino/stm32/stm32yyxx_hal_conf.h

This file handles:

  • mandatory HAL modules definition the default list of modules to be used in the HAL driver
  • HAL module enabled by default which can be disabled
  • HAL modules not defined by default

Extra HAL configuration can be enabled/disabled in variant.h (if required) or in a file named (at sketch level):

  • hal_conf_extra.h

Custom HAL configuration file can replace the default one by adding a file named (at sketch level):

  • hal_conf_custom.h

HAL modules configuration

Below HAL modules or definitions are listed for convenience but may not be up to date. Refer to cores/arduino/stm32/stm32yyxx_hal_conf.h to make sure having up to date values.

Mandatory HAL module enabled by default

  • HAL_MODULE_ENABLED
  • HAL_CORTEX_MODULE_ENABLED
  • HAL_DMA_MODULE_ENABLED: Required by other modules
  • HAL_FLASH_MODULE_ENABLED
  • HAL_GPIO_MODULE_ENABLED
  • HAL_PWR_MODULE_ENABLED
  • HAL_RCC_MODULE_ENABLED

HAL module enabled by default which can be disabled

  • HAL_ADC_MODULE_ENABLED
  • HAL_I2C_MODULE_ENABLED
  • HAL_RTC_MODULE_ENABLED
  • HAL_SPI_MODULE_ENABLED
  • HAL_TIM_MODULE_ENABLED

HAL modules not defined by default

  • HAL_DAC_MODULE_ENABLED
  • HAL_ETH_MODULE_ENABLED
  • HAL_SD_MODULE_ENABLED
  • HAL_QSPI_MODULE_ENABLED

HAL modules not defined, handled thanks Arduino menu

  • HAL_UART_MODULE_ENABLED
  • HAL_PCD_MODULE_ENABLED

List of HAL_*_MODULE_DISABLED definition

  • HAL_ADC_MODULE_DISABLED
  • HAL_I2C_MODULE_DISABLED
  • HAL_RTC_MODULE_DISABLED
  • HAL_SPI_MODULE_DISABLED
  • HAL_TIM_MODULE_DISABLED
  • HAL_DAC_MODULE_DISABLED
  • HAL_EXTI_MODULE_DISABLED: interrupt API does not used HAL EXTI module anyway API is cleaned with this
  • HAL_ETH_MODULE_DISABLED
  • HAL_SD_MODULE_DISABLED
  • HAL_QSPI_MODULE_DISABLED

Disable unused features can reduce significantly FLASH and RAM usage.

Example of Blink.ino for Nucleo-L031K6 with 32768 bytes of Flash and 8192 bytes of RAM:
Flash Size(%) RAM Size(%)
Default (Serial enabled) 11152 (34%) 780 (9%)
HAL disabled* 4292 (13%) 52 (0%)
diff size(%) -6860 (-21%) -778 (-9%)

*With all HAL_*_MODULE_DISABLED defined in hal_conf_extra.h and Serial disabled

Other HAL configuration

Below HAL configurations are listed for convenience but may not be up to date. Refer to the required default STM32 HAL configuration file stm32yyxx_hal_conf_default.h in system/STM32YYxx/ (where YY is the MCU serie) to make sure having up to date values.

Oscillator Values adaptation

Hereafter, list of possible oscillator values which can be redefined:

  • HSE_VALUE: Value of the External oscillator in Hz
  • HSE_STARTUP_TIMEOUT: Time out for HSE start up, in ms
  • MSI_VALUE: Value of the Internal Multiple Speed oscillator in Hz
  • CSI_VALUE: Value of the Internal oscillator in Hz
  • HSI_VALUE: Value of the Internal High Speed oscillator in Hz
  • HSI_STARTUP_TIMEOUT: Time out for HSI start up, in ms
  • HSI14_VALUE: Value of the Internal High Speed oscillator for ADC in Hz. The real value may vary depending on the variations in voltage and temperature.
  • HSI48_VALUE: Value of the Internal High Speed oscillator for USB in Hz. The real value may vary depending on the variations in voltage and temperature.
  • LSI_VALUE: Value of the Internal Low Speed oscillator in Hz. The real value may vary depending on the variations in voltage and temperature.
  • LSI1_VALUE: Value of the Internal Low Speed 1 oscillator in Hz. The real value may vary depending on the variations in voltage and temperature.
  • LSI2_VALUE:Value of the Internal Low Speed 2 oscillator in Hz. The real value may vary depending on the variations in voltage and temperature.
  • LSE_VALUE: Value of the External Low Speed oscillator in Hz`
  • LSE_STARTUP_TIMEOUT: Time out for LSE start up, in ms
  • EXTERNAL_CLOCK_VALUE: External clock source for I2S peripheral
  • EXTERNAL_SAI1_CLOCK_VALUE: Value of the SAI1 External clock source in Hz
  • EXTERNAL_SAI2_CLOCK_VALUE: Value of the SAI2 External clock source in Hz

HAL system configuration

Hereafter, list of possible HAL system configuration values which can be redefined:

  • VDD_VALUE: Value of VDD in mv
  • TICK_INT_PRIORITY: tick interrupt priority
  • PREFETCH_ENABLE: To enable prefetch
  • INSTRUCTION_CACHE_ENABLE: Use to enable I-cache
  • DATA_CACHE_ENABLE: Use to enable D-cache
  • USE_SPI_CRC: Use to activate CRC feature inside HAL SPI Driver
  • ART_ACCLERATOR_ENABLE: To enable ART Accelerator
  • USE_SD_TRANSCEIVER: To use µSD Transceiver

HAL module only

STM32 peripherals have many powerful features. Some of them are used by default by the Arduino API: I2C, SPI, TIM, U(S)ART, ... and take over IRQ Handlers (ex: TIMx_IRQHandler) and other HAL weaked functions (ex: HAL_XXX_MspInit()). For advanced user applications, it could be useful to take control of those IRQ handlers.

Since core version greater than 1.7.0, it is possible to disable the use of the HAL modules by the Arduino API.

Defining HAL_PPP_MODULE_ONLY in build_opt.h or hal_conf_extra.h allows HAL peripheral (PPP ) module usage without any usage by the core.

Hereafter list of possible definition:

  • HAL_UART_MODULE_ONLY
  • HAL_TIM_MODULE_ONLY
  • HAL_ADC_MODULE_ONLY
  • HAL_DAC_MODULE_ONLY
  • HAL_RTC_MODULE_ONLY
  • HAL_PWR_MODULE_ONLY

I2C and SPI do not required definition as used only thanks built-in library. Do not include Wire.h or SPI.h will allow to use the HAL module.

Home

Clone this wiki locally